b'ROUGH OPENINGSPATIO SYSTEMS ROUGH OPENINGS RETRO-FIT SIZENOMINALDOOR UNITROUGHOPENING SIZE OUTSIDE DOOR SIZE ACTUAL SIZE (WOOD STUD) BRICKMOULD SIZEWIDTH HEIGHT WIDTH HEIGHT WIDTH HEIGHT* WIDTH HEIGHT*5\'0" 6\'8" 59-1/4" 79-1/2" 60" 80" 61-3/4" 80-3/4"DOUBLE5\'0" 8\'0" 59-1/4" 95-1/2" 60" 96" 61-3/4" 96-3/4"(FRENCH)6\'0" 6\'8" 71-1/4" 79-1/2" 72" 80" 73-3/4" 80-3/4"6\'0" 8\'0" 71-1/4" 95-1/2" 72" 96" 73-3/4" 96-3/4"TRIPLE 9\'0" 6\'8" 106-7/8" 79-1/2" 107-5/8" 80" 109-3/8" 80-3/4"(FRENCH)5\'0" 6\'8" 59-3/4" 79-1/2" 60-1/2" 80" 62-1/4" 80-3/4"DOUBLE 5\'0" 8\'0" 59-3/4" 95-1/2" 60-1/2" 96" 62-1/4" 96-3/4"(CENTER-SWING) 6\'0" 6\'8" 71-3/4" 79-1/2" 72-1/2" 80" 74-1/4" 80-3/4"6\'0" 8\'0" 71-3/4" 95-1/2" 72-1/2" 96" 74-1/4" 96-3/4"TRIPLE 9\'0" 6\'8" 107-1/4" 79-1/2" 108" 80" 109-3/4" 80-3/4"(CENTER-SWING)How to Measure Your DoorSTEP 1. Measure the width of your existing door slab.This is the edge of one side of the door slab to the edge of the other sideof the door slab. (A) STEP 2. Measure the height of your existing door slab.This is the top edge of the door slab to the bottom edge of the door slab.B Do not include the sweep on the bottom of the door. (B)STEP 3. Measure the jamb depth of your existing door.This is the inside edge of the door jamb to the outside edge of the door jambA (area where hinges are). Do not include any trim in this measurement.STEP 4. Determine the handing of your existing door.A) All handing must be done from the exterior of the door. Looking at your door C)Select the combination below from the outside, your door swings: to determine the properAInto the house (inswing) handing of your door.BOut of the house (outswing)AARight-Hand InswingB) Looking at your door from theABLeft-Hand Inswingoutside, your door knob is: BALeft-Hand Outswing AOn the left side of the doorBBRight-Hand Outswing IMPORTANTBOn the right side of the doorThere is no industry standardSTEP 5. Determine final calculations of your existing door.for door sizing, so follow theseTo find the estimated size of your existing unit, use the calculations below. steps carefully. MeasuringWIDTH FOR INSWING UNITS FOR OUTSWING UNITSyour door and determiningMeasurement Ayour door handing are veryAdd for Jambs 1-3/4" 1-3/4"important to ensure the bestTotal Unit Widthfit for your opening. For bestHEIGHTresults, have a professionalMeasurement Bmeasure your opening andAdd for Head & Sill 2-1/2" 1-5/8"install your door.Total Unit Heightmasonite.com 217'